Maximum gate width 10-feet. Maximum gate weight 300 pounds DKS 6400 installs underground making it virtually invisible and satisfies the most sophisticated automation needs without being detrimental to the original gate design. Invisible and powerful, the motor/drive mechanism is constructed in die-cast aluminum with a special corrosion-proof treatment, and because the drive unit is gear driven, there is no need to worry about hydraulic leaks, check valves or pumps. The underground self-supporting foundation box is built from corrosion-proof steel and has a galvanized steel cover. A lockable manual release lever is designed so that it can be operated from inside or outside the gate. |
Maximum gate width 18-feet. Maximum gate weight 700 pounds Doorking Gate Openers Model 6300 with 1 HP Motor Maximum gate width 22-feet. Maximum gate weight 800 pounds DKS 6300 series are designed to operate vehicular swing gates in residential, commercial and industrial applications. DKS 6300 are designed so that they can be either pad or post mounted without any costly and time consuming field modifications. You need to specify which mounting method when ordering. The unique design of these allow the gate arm to be attached to the bottom rail of the gate. This eliminates the need for any brackets to be welded to the face of the gate and creates an aesthetically pleasing installation. DKS 6300 can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage. |
Maximum gate width 14-feet. Maximum gate weight 500 pounds*. Doorking Gate Operators Model 6050 Maximum gate width 10-feet. Maximum gate weight 400 pounds*. DKS 6050 and DKS 6100 are designed to operate vehicular swing gates in residential and commercial applications. These are designed so that they can be either pad or post mounted without any costly and time consuming field modifications. You need to specify which mounting method when ordering. The unique design of these operators allows the gate arm to be attached to the bottom rail of the gate. This eliminates the need for any brackets to be welded to the face of the gate and creates an aesthetically pleasing installation. The 6100 can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage. |
The DKS 6002 offers convenience and reliability in a compact design. The actuator mounts directly on your gate and pilaster, simplifying installation and eliminating the need for concrete pads. The elegant lines obtained by using extruded aluminum material provide a clean profile that will blend in with any gate design. But beauty is not just skin deep with the DKS actuator. The powerful screw driven piston connects directly to the gate eliminating weak mechanical connections and it is fully enclosed to prevent dirt and other airborne corrosives from contaminating the screw threads. And there is no need to worry about hydraulic leaks, check valves or pumps. |
Door king Slide Gate Openers Model 9050 Maximum gate length 16-feet. Maximum gate weight 300 pounds Doorking Slide Gate Operators Model 9070 Maximum gate length 22-feet. Maximum gate weight 500 pounds DKS 9050 and DKS 9070 are designed to operate vehicular slide gates in residential and light-duty commercial applications only. DKS 9050 or 9070 are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, they can be pad or post mounted to meet any installation requirements. |
Doorking Sliding Gate Operators Model 9100 Maximum gate length 30-feet. Maximum gate weight 1000 pounds DKS 9100 is designed to operate vehicular slide gates in residential and commercial applications. The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operator can be pad or post mounted to meet any installation requirements. |
Door king Slide Gate Operators Model 9150 with 1/2 HP Motor Maximum gate weight 1000 pounds Doorking Sliding Gate Openers Model 9150 with 1 HP Motor Maximum gate length 45-feet. Maximum gate weight 1500 pounds DKS 9150 are designed to operate vehicular slide gates in residential, commercial and industrial applications. DKS 9150 are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, it can be pad or post mounted to meet any installation requirements. The 9150 can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage. |
Maximum gate length 100-feet Maximum gate weight 3000 pounds DKS Slide Gate Openers Model 9220 Maximum gate length 100-feet. Maximum gate weight 2000 pounds DKS Sliding Gate Operators Model 9230 Maximum gate length 100-feet. Maximum gate weight 5000 pounds DKS Maximum Security are designed to operate vehicular slide gates in limited (Class III) and restricted (Class IV) applications only. The 9200 Series should never be used in applications serving the general public. These are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. Center mounting the operator requires an optional pedestal mounting base. The speed control on the 9220 and 9230 models allows the user to set the speed of the gate from 1/2 to 2 feet/sec., and provides slow-start and slow-stop functions as well. |
Doorking Heavy Duty Gate Openers Model 9530 Maximum gate length 100-feet. Maximum gate weight 5000 pounds Door King Heavy Duty Gate Operators Model 9550 Maximum gate length 160-feet. Maximum gate weight 10,000 pounds DKS 9530 and DKS 9550 are designed to operate very heavy vehicular slide gates in limited (Class III) and restricted (Class IV) applications only. 9530 or 9550 Series should never be used in applications serving the general public. DKS 9530 or 9550 are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. They include a speed control module which allows the user to set the speed of the gate from 1/2 to 2 feet/sec. in the model 9530; and 1/2 tp 4 feet/sec in the model 9550. Each of these have a slow-start and slow-stop function as well. Additionally, a "Panic Close" input (model 9530 only) increases the gate speed up to 6 Ft./sec in the closing cycle. |
Doorking Gate Operators Model 9310 1/2 HP Maximum gate length 30-feet. Maximum gate weight 1000 pounds Door King Gate Openers Model 9310 1 HP Maximum gate length 45-feet. Maximum gate weight 1500 pounds DKS 9310 is designed to operate vehicular slide gates in residential and commercial applications. The 9310 is designed so that it can easily be mounted in the front or rear of the gate without any costly and time consuming field modifications. These are designed to be pad mounted. The 9310 is available in 1/2 or 1 HP versions and can be equipped with a factory installed DC Convenience Open option which will automatically open the gate in the event of a power outage. |
Doorking Arm Barrier Gate Operators Model 1601 1/2 HP continuous-duty motor. 115, 230*, 460* VAC. (*230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.) DC powered convenience open. 14-foot round aluminum arm. 14-foot wood arm. Wood arm folding bracket for low headroom. 12-foot plastic arm. Plastic arm folding bracket for low headroom. DKS 1601 is designed for single lane (14 ft. max) vehicular traffic control in high traffic commercial and industrial applications. The 1601 is designed so that it can be mounted on either the left or right hand side of the roadway. They can be equipped with a DC convenience open package (optional) that will automatically raise the arm in the event of a power outage. |
Door King Barrier Gate Openers Model 1602 1 HP continuous-duty motor. 60:1 gear-box running in a continuous oil bath. 115, 230*, 460* VAC. (*230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.) DC powered convenience open. 20-foot three-piece wood arm - counter balanced DKS 1602 is designed for traffic lanes up to 20-feet wide in low use commercial and industrial applications. The 1602 uses a counter-balanced three-piece wishbone style arm assembly. The 1602 is designed so that it can be mounted on either the left or right hand side of the roadway. The operator can be equipped with a DC convenience open package (optional) that will automatically raise the arm in the event of a power outage. |
Maximum gate width 10-feet. DKS 6003 swing gate actuator offers convenience and reliability in a compact design. It mounts directly on your gate and pilaster, simplifying installation and eliminating the need for concrete pads. ADVANCED FEATURES Internal adjustable limit switches. Slow start / slow stop. Overlap feature for dual swing gate operation. Magnetic lock output. Ports for plug-in loop detectors. |
Maximum gate width 18-ft. (1/2 HP) or 22-ft. (1 HP). Maximum gate weight 700 pounds* (1/2 HP) or 800 pounds* (1 HP). DKS 6500 is designed for residential, commercial and industrial applications for both single and dual-leaf gates. The unique design of these allow for easy access to the electronics and mechanical areas of the operator without ever having to remove the gate arm. This simplifies installation and maintenance. The electronic magnetic limits will never wear out or break and they are easily adjusted. The solid steel frame and belt driven gear box make this operator one of the quietest vehicular gate operators on the market today |
About Us | Contact Us | Our Policies | FAQ | Manufactures | Links | Copyright Protected 2004-2008 - L. A. Ornamental & Rack Corp. All rights reserved. No part of this site can be reproduced in any form or by any means, electronic, mechanical, photocopying, or otherwise without prior written consent of L. A. Ornamental & Rack Corp. 3708 NW 82nd Street Miami Florida 33147, Office: 305-696-0419 Fax: 305-696-0461 E-Mail: LAOrnamental@Aol.com |
L. A. Ornamental & Rack Corp 3708 NW 82nd Street Miami, Florida 33147 Office: 305-696-0419 Fax: 305-696-0419 LAOrnamental @Aol.com |
Doorking 1603 Barrier Arm Operator with Auto Spike System 1/2 HP continuous-duty motor. 115, 230°, 460° VAC. (*230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.) 40:1 gear-box running in a continuous oil bath. Arm rotates 90° in approximately 1.5 seconds. Class II, III and IV applications. Compliant with UL 325 and 991 The DKS model 1603 Barrier Gate Operator / Automated Spike System is designed as a modular system allowing for easy flexibility in different applications and easy installation. The 1603 operator is designed with many advanced features and mechanically links the spikes to the barrier arm. The 1603 auto-spike system is ideal for parking lots, rental car agencies, schools, car dealerships, government agencies, or in any application where a higher degree of traffic control is preferred |
DoorKing Gate Openers or Operators - Sliding or Swing Gate Openers - Residential or Commercial Operators - Heavy Duty Automatic or Electric Gate Operators - Arm Barrier Operators Click here for complete prices on all DoorKing Gate Openers and Accessories Circuit Boards Telephone Entry Systems Entry System Circuit Boards |
|
Doorking 6004 Column Mount Swing Gate Operator: The DKS residential column mount swing gate operator offers convenience and reliability in a compact design. The Model 6004 is ideal to operate swing gates that are mounted on large columns. The 6004 mounts directly on the column and simplifies installation by eliminating the need to cut niches on the column and there is no need for concrete pads. Using a strong gear reduction system, there is no need to worry about hydraulic leaks, check valves or pumps. The 6004 features a keyed release system that allows the gate to be moved by hand if a system failure should occur. |
Doorking 9000 Vehicular Slide Gate Operator The DKS 9000 series of slide gate operators offer convenience, reliability and safe operation in a small, compact design. These operators are ideally used in residential, commercial or industrial high-use applications. The steel frame and belt drive/gear-box reduction system provide a powerful, yet extremely quiet, slide gate operation. The 9000 uses an advanced microprocessor control circuit with outstanding features. Designed with versatility in mind, these operators will fit most slide gate operation requirements. |