|L. A. Ornamental & Rack Corp
3708 NW 82nd Street
Miami, Florida 33147
|About Us | Contact Us | Our Policies | FAQ | Manufactures | Links |
Copyright Protected 2004-2008 - L. A. Ornamental & Rack Corp. All rights reserved. No part of this site can be reproduced in any form or by
any means, electronic, mechanical, photocopying, or otherwise without prior written consent of L. A. Ornamental & Rack Corp.
3708 NW 82nd Street Miami Florida 33147, Office: 305-696-0419 Fax: 305-696-0461 E-Mail: LAOrnamental@Aol.com
|Linear AP-4 Gate Access Receiver
• Ideal for gated communities, parking facilities, and
• Easy to set-up and use — up to 480 remotes can be
programmed with a few keystrokes.
• Easy to add, suspend, and delete transmitters through
programming mode — no transmitter dip switches to
• Supports 480 block coded transmitters or 238
individual ransmitters/wireless keypad entry codes.
• Supports one fully supervised safety edge transmitter.
|For sites that have a single entrance or gate, the AP-4 is the ideal wireless-based access control system. It
can be used to remotely activate devices such as gate operators, door strikes, or door operators. Based on
and priced the same as the proven AP-3 access controller, the AP-4 is small enough to be mounted within
the gate operator. It represents a tremendous value over older dip switch style products that are priced
nearly the same. The AP-4 has a built-in radio receiver. It has a 250 foot range that can be extended even
farther with an optional EXA-2000 antenna.The AP-4 is compatible with all MegaCode format transmitters,
which come factory programmed with one of over 1,000,000 possible codes, all but eliminating any chance
of duplication. It accepts either 480 block coded transmitters or 238 individual
transmitters or wireless keypad entry codes. For the latter, the AP-4 can be used with Linear’s wireless
MDKP keypad, which accepts user codes of two to six digits and transmits them to the AP-4 controller.
Two relay outputs are provided: one for gate or door access; the other for obstacle control using the MGT,
the industry’s only supervised safety edge transmitter. The AP-4 looks for an hourly status transmission
from the MGT to report on transmitter functionality, battery condition, and case integrity. If any of those
conditions require attention, the AP-4 will alert the user by beeping once every five seconds.The user must
then activate the transmitter twice in order for the AP-4 to grant access. Installation and set-up are simple.
The AP-4 operates on 12-24 volts, ac or dc. It can be powered directly from
the radio power output of most gate operators. Learning, suspending, or deleting transmitters is as simple
as pressing a few keys on the AP-4’s built-in keypad. Program data is stored in non-volatile EEPROM; data
retention is in excess of ten years, even in the event of a power failure.
Relay: two form“C” relays, rated at 1 amp @ 24 volts ac or dc; one for control and one for obstacle
Display: three seven-segment displays to provide system activity and program data; LEDs used in
conjunction with displays to provide transmitter and radio activity
RF: integral 318 MHz super regenerative receiver @ -94 dBm sensitivity (nominal); receives MegaCode
Open Request: terminal input and button activation triggers the control relay
Keypad: integral 16-key membrane style keypad with tactile feedback
12 to 24 volts ac or dc, 250 mA maximum
-22° to +170°F (-30° to +77°C)
3.625 in W x 5.25 in H x 1.5 in D (92 x 133 x 38 mm)
AP-4 controller; supports 480 MegaCode block coded transmitters or 238 individual transmitters/wireless
keypad entry codes, plus one MGT safety edge transmitter; 9-1/2 inch whip antenna; 3 feet of coaxial cable;
a. EXA-1000: remote, omnidirectional; includes mounting hardware and five feet of cable
b.EXA-2000: remote, directional-type; includes mounting hardware and ten feet of cable
Wireless Keypad: Linear’s MDKP
Transmitters: any of Linear’s many MegaCode models
|BFT Cell Phone Entry with
Keypad up to 1000 User --
Open Your Gate From any
where in the world Click here