 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| L. A. Ornamental & Rack Corp 3708 NW 82nd Street Miami, Florida 33147 Office: 305-696-0419 Fax: 305-696-0461 |
| Viking Control Board DUPCB10 or Circuit Board DUMSCB10 Slave for G5 and X9 The Gate Operator requires a single phase AC line to operate and charge the batteries. A Master/Slave control board is available, when required, to run two gate operators in synchronous mode. Vehicle loop detectors must be installed to decrease the possibility of vehicle entrapment on the gate. The SECONDARY ENTRAPMENT PROTECTION like the edge sensor and the photoelectric beam MUST BE PART OF EVERY SINGLE INSTALLATION to prevent pedestrian or animal entrapment. Viking control board or Viking Circuit Board provides two modes of operation that a radio receiver can control the gate. External supply for the magnetic lock must be provided. This will prevent rapid drainage of the battery in the event of power failure. External supply for the solenoid connection must be provided. This will prevent rapid drainage of the battery in the event of power failure. The guard station provides control of the gate operator to open, stop and close the gate. The Obstruction Sensor detects obstructions in the path of the traveling gate. The Trim Pot for the Obstruction Sensor adjusts the sensitivity level that triggers the Sensor. The gate operator contains a unique design that allows the user to move the gate manually in case of power failure. There are three levels of force required to move the gate manually. Minimum Force: By removing the wire-jumper plug from the “Fail Safe/Secure” connector: The gate can be move manually with relative low amount of force. Maximum Force: By inserting the wire-jumper plug into the “Fail Safe/Secure” connector: The gate can still be move by hand with relative high amount of force. Manual Operation Locked By removing the “Break Release Pin” from the operator: The gate can’t be moved manually. The Hold Open Timer function holds the gate at the open position for a predetermined amount of time, prior to closing automatically. Set the Timer to the desired time, from 1 to 60 seconds. Setting the Overlap Delay Pot to “0” will cause the master and the slave units to open and close at the same time. |
Viking Access Systems is a manufacturer of sleek, high tech and innovative
gate operators. Viking Access is continuously working hard to identify and
design products that will appeal to the access control industry and it’s
needs. Their in-house engineering department designs, produces, and
tests the latest technology of today and tomorrow without limitations.
gate operators. Viking Access is continuously working hard to identify and
design products that will appeal to the access control industry and it’s
needs. Their in-house engineering department designs, produces, and
tests the latest technology of today and tomorrow without limitations.
| Viking Control Board, Viking DUPCB10 |
| Viking Control Board, Viking DUMSCB10 Master Slave G5 and X9 |
Viking Gate Operators use the same Circuit Board on all Viking Gate Openers. The Only
Difference is if your going to use or replace a Master Slave Circuit Board. If not sure as to
what board you need or if you would like to Check Availability for your Viking Gate Operator
don't hesitate to Contact Us.
Difference is if your going to use or replace a Master Slave Circuit Board. If not sure as to
what board you need or if you would like to Check Availability for your Viking Gate Operator
don't hesitate to Contact Us.
| About Us | Contact Us | Our Policies | FAQ | Manufactures | Links | Copyright Protected 2004-2008 - L. A. Ornamental & Rack Corp. All rights reserved. No part of this site can be reproduced in any form or by any means, electronic, mechanical, photocopying, or otherwise without prior written consent of L. A. Ornamental & Rack Corp. 3708 NW 82nd Street Miami Florida 33147, Office: 305-696-0419 Fax: 305-696-0461 E-Mail: LAOrnamental@Aol.com |
| ||||||||||
| ||||||||||